manualshive.com logo in svg

Kyocera Copystar CS-1635, Service Manual

The Kyocera Copystar CS-1635 is a reliable office copier known for its exceptional performance and user-friendly interface. Enhance your productivity with this versatile device by easily accessing its Service Manual. You can download the manual for free from our website, empowering you to troubleshoot and optimize its functionalities.

Share
Download
background image

2HA/2HB

1-6-1

1-6 Requirements on PWB Replacement

1-6-1

 Upgrading the firmware on the main PWB

Follow the procedure below to upgrade the firmware on the main PWB, engine PWB or language software.

Firmware upgrading requires the following tools:
Flash DIMM (P/N 2C968131)

Procedure

1. Run maintenance mode U019 to check the 

version of the ROM.

2. Turn the power switch off and disconnect 

the power plug.

3. Remove the rear cover and change the 

jumper switch position on the main PWB to 
the right side.

4. Insert the DIMM into the DIMM slot on the 

main PWB. Insert the power plug and turn 
the power switch on.

5. Upgrading firmware starts and the status is 

displayed on the operation panel.

6. When the upgrade operation is complete, 

the checksum will be displayed and a beep 
indicating the completion will sound.

7. Turn the power switch off and disconnect 

the power plug, remove the DIMM from the 
main PWB, and return the jumper switch to 
its original position. Reattach the rear cover 
to its original position.

8. Insert the power plug and turn the power 

switch on.

9. Run maintenance mode U019 to check that 

the version of the ROM has changed.

Figure 1-6-1

Jumper switch

DIMM slot

Summary of Contents for Copystar CS-1635





















































































































































































































































Reviews:

No comments

Related manuals for Copystar CS-1635

Pandigital ZINK PANPRINT01 Quick Start Manual preview
ZINK PANPRINT01
Brand: Pandigital Pages: 2
Gainscha GA-S300 User Manual preview
GA-S300
Brand: Gainscha Pages: 12
Oki MC561 Maintenance Manual preview
MC561
Brand: Oki Pages: 276
Brightek U04 Quick Install Manual preview
U04
Brand: Brightek Pages: 8
Lexmark MS310d Quick Refence Manual preview
MS310d
Brand: Lexmark Pages: 79
Oki ES8473 Maintenance Manual preview
ES8473
Brand: Oki Pages: 271
Dremel DigiLab 3D40 FLEX Quick Start Manual preview
DigiLab 3D40 FLEX
Brand: Dremel Pages: 4
Xerox AltaLink C81 Series User Manual preview
AltaLink C81 Series
Brand: Xerox Pages: 412
Riso MZ1070 Technical Manual preview
MZ1070
Brand: Riso Pages: 150
Konica Minolta BIZHUB C3351 Quick Start Manual preview
BIZHUB C3351
Brand: Konica Minolta Pages: 102
Ricoh Schmidt 3 Installation Manual preview
Schmidt 3
Brand: Ricoh Pages: 8
L-Mark LK-330E User Manual preview
LK-330E
Brand: L-Mark Pages: 62
Kyocera ECOSYS M2135dn Operation Manual preview
ECOSYS M2135dn
Brand: Kyocera Pages: 410
Canon LBP228x Getting Started preview
LBP228x
Brand: Canon Pages: 32
Canon LBP5000 Series Service Manual preview
LBP5000 Series
Brand: Canon Pages: 162
Canon LBP-8iv Parts Catalog preview
LBP-8iv
Brand: Canon Pages: 170
Canon LBP246dw Setup Manual preview
LBP246dw
Brand: Canon Pages: 184
Canon LBP 2900i User Manual preview
LBP 2900i
Brand: Canon Pages: 314

Brands by name

Popular brands

Load more brands