Kyocera Copystar CS-1635 Service Manual Download Page 153

Page: 153 / 244

2HA/2HB

1-5-27

1-5-6

Transfer section

(1) Detaching and refitting the transfer roller

Follow the procedure below to replace the transfer roller.

Procedure

1. Remove the paper conveying unit (see page

1-5-7).

2. Remove the screw holding each of the front

and rear release lever stoppers and then the
stoppers from the release lever shaft.

Figure 1-5-56

3. Detach the fitting portions located

on the front and rear and then
remove the transfer roller from the
paper conveying unit.

4. Replace the transfer roller and

refit all the removed parts.

Figure 1-5-57

Paper conveying unit

Rear release
lever stopper

Front release
lever stopper

Transfer roller

Fitting portion

Paper conveying unit

Summary of Contents for Copystar CS-1635





















































































































































































































































Search results

Summary of Contents for Copystar CS-1635

Reviews:

Related manuals for Copystar CS-1635

Brands by name

Popular brands

Kyocera Copystar CS-1635, Service Manual

Search results

Summary of Contents for Copystar CS-1635

Reviews:

Related manuals for Copystar CS-1635

Brands by name

Popular brands