KYLAND Technology PTS-DR200 Operation Manual Download | Manualshive

Page: 49 / 55

background image

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 47 -

[Figure 3-30] Route Screen

The current routing table will be listed on the bottom of screen.
Press ‘Add’ to add a static route for PTS-DR200 time server.
Press ‘Del’ to delete the selected route information.

3.6.3. Configuration

Press ‘Configuration’ on the left navigation bar to manage configuration file.
The configuration screen will be shown as:

[Figure 3-31] Configuration Screen

Press ‘Backup’ to backup configuration file and system will pop-up a tip window, let
user to select a directory to save configuration file. The name of configuration file is
named by MAC address.

Press ‘Restore’ to restore a configuration by WEB. Before do it, please select a file.
After press ‘Restore’, the system will active your selected configuration file.

3.6.4. Firmware

Press ‘Firmware’ on the left navigation bar to upgrade firmware.
The firmware screen will be shown as:

«
...
47
48
49
50
51
...
»

Summary of Contents for PTS-DR200
























































Reviews:

No comments

Related manuals for PTS-DR200

Brand: US Robotics Pages: 156

Brand: Socket Pages: 28

10/100M 32bit Fast Ethernet PC card

Brand: LevelOne Pages: 51

Brand: ASUSTOR Pages: 11

Brand: ZyXEL Communications Pages: 7

Brand: Ratoc Systems Pages: 16

USB CF Host Card REX-CFU1

Brand: Ratoc Systems Pages: 21

Brand: Oracle Pages: 262

Brand: RAK Pages: 71

Brand: National Instruments Pages: 23

Brand: Gigabyte Pages: 35

Brand: Omega Engineering Pages: 250

Catalyst 4500 Series

Brand: Cisco Pages: 2086

Optional i350 Quad Port 1 GbE Card

Brand: Quantum Pages: 12

Brand: Audio enhancement Pages: 3

Brand: D-Link Pages: 24

HyperNet HYNEP61001

Brand: Hypertec Pages: 7

Brand: Hypertec Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands