KYLAND Technology KIEN3016A Hardware Installation Manual Download Page 5 | Manualshive

Page: 5 / 19

KYLAND Technology KIEN3016A Hardware Installation Manual Download Page 5

5

1. Packing List

KIEN3016A Industrial Ethernet Switch

1

Hardware Installation Manual 1

Certificate of Quality (including Warranty Card) 1

Note

: After unpacking, please check the accessories and the appearance of the equipment. If

anything is missing or damaged, please contact us.

2. Product Overview

KIEN3016A is a series of green, low power consumption and compact DIN-Rail

industrial Ethernet switch that can be applied extensively in wind power,

distribution network automation,subway PIS, power SCADA, wastewater

treatment, metallurgy, intelligent transportation, rail transit and many other

industries.

KIEN3016A industrial Ethernet switch supports DIN-Rail and panel mounting.It

supports IP40 protection class.

3. Structure and Interface

3.1Front Panel

KIEN3016A supports two kinds of product models.The interface is different for

each product model.

z

KIEN3016A-2S/M-14T front panel is shown in Figure 1 below

«
...
3
4
5
6
7
...
»

Summary of Contents for KIEN3016A




















Reviews:

No comments