KVH Industries TracPhone FB150 User Manual Download

Page: 48 / 140

Chapter 4: Using the web interface

Entering the SIM PIN in the web interface

Entering the SIM PIN in the web interface

Do you need a SIM PIN?

If a computer is connected when you start up the terminal, you can access the web

interface and enter the SIM PIN here.

To enter the SIM PIN

If your SIM card requires a PIN, and the PIN has not yet been entered, you must

enter it. When you access the web interface, it opens on the PIN page. Until you have

entered the PIN you can only upload software and view the DASHBOARD. Access

to all other parts of the web interface requires a PIN.
For information on how to enter the SIM PIN, see

Entering the SIM PIN using the web

interface

on page 16.

When the correct PIN has been entered, the web interface opens the Dashboard and

is ready for use.

Note

You may not have to enter a SIM PIN to access the terminal. This depends

on whether or not the use of a SIM PIN is enabled on your SIM card.
The administrator can enable and disable the use of a SIM PIN. For details,

see

Setting up the use of SIM PIN in the terminal

on page 96.

Note

Using an Administrator user name and password you can change the PIN

and enable or disable the use of a PIN. For further information, see

Setting

up the use of SIM PIN in the terminal

on page 96.

Note

Some parts of the web interface may be greyed out if the user permissions

are limited. For information on how to set up user permissions, see

Setting

up user permissions

on page 98.

Summary of Contents for TracPhone FB150













































































































































Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands

KVH Industries TracPhone FB150, User Manual

Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands