KVH Industries TracPhone FB150 User Manual Download

Page: 120 / 140

Chapter 5: Troubleshooting

Status signaling

111

List of events

The following list explains the events that may show in the web interface of the

terminal.

Note

Events with “Info” level are not included in this list. Only events that can

appear in the alarm list and cause a warning icon

in the web interface

are included.

Event Text

Explanation

Remedy

00100 to

00199

System data

damaged

Important system data is

damaged.

Do not use the terminal.

Contact your dealer/

distributor.

00210 to

00219

SIM module

error

The SIM interface on the

terminal cannot be used.

Contact your dealer/

distributor.

00240 to

00249

Temperature

sensor error

The terminal is in danger

of overheating.

Do not use the terminal.

Contact your dealer/

distributor.

00260 to

00269

System error

The terminal cannot

communicate on the

satellite network.

Contact your dealer/

distributor.

00270 to

00279

Voice module

error

Voice services cannot be

accessed by the terminal.

Contact your dealer/

distributor.

00280 to

00289

Ethernet module

error

The Ethernet interface on

the terminal cannot be

used.

Contact your dealer/

distributor.

00300 to

00309

GPS module

error

The GPS module is out of

function. The terminal

cannot obtain a valid GPS

position.

Contact your dealer/

distributor.

00340 to

00349

2-wire failure

The Phone interface of the

terminal cannot be used.

Contact your dealer/

distributor.

00350 to

00359

AD9864

calibration

data error

Internal error in the

receiving part of the

terminal.

Contact your dealer/

distributor if the problem

persists.

00360 to

00369

No antenna

found

The terminal cannot

communicate with the

antenna.

• Check the cable

between terminal and

antenna.

• Reboot the terminal.

Summary of Contents for TracPhone FB150













































































































































Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands

KVH Industries TracPhone FB150, User Manual

Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands