Kval 994-X Operation Manual Download Page 75

Page: 75 / 130

Check Specifications of the Front Section

3-15

KVAL 994-X Operation Manual

Step 4: (Option CH) Chisel Calibration

Once the routers are calibrated, the chisels need to be checked. In order to verify the chisels, a

door and a jamb will be required for this procedure.

Load in a known hinge pattern and make sure the chisels are turned on. Run one

hinge for this calibration.

Check that the H-block is setup in the correct location.

Run the hinge.

After the hinge run is finished, check all four corners of the hinge to see if the chis

els are in the correct location.

If the corners of the hinge are out of specification, continue the process on the next

page.

Select button to gain access to the Chisel Calibration menu.

Adjusting the Chisels

Identify the corner or comers to be calibrated.

a.Upper Left Chisel
b.Upper Right Chisel
c.Lower Left Chisel
d.Lower Right Chisel.

Upper Left

Chisel

Lower Left

Chisel

Lower Right

Chisel

Upper Right

Chisel

Door

Jamb

Summary of Contents for 994-X



































































































































Search results

Summary of Contents for 994-X

Reviews:

Related manuals for 994-X

Brands by name

Popular brands

Kval 994-X, Operation Manual

Search results

Summary of Contents for 994-X

Reviews:

Related manuals for 994-X

Brands by name

Popular brands