Point Source Lighting
Westwood, New Jersey 07675
Fax 201 664 4801
INSTALLATION INSTRUCTIONS
SQUARE DIRECTIONAL
J2333, J2335, & J2337
Junction
Box
Inner
Cover
T
-approx.
1/4"" Jlh dlrecllons
(left to right
/
forward and backward)
Note: If required:
I
Fig. 1
Before ceiling is closed, loosening of wing nuts
allows square aperture to be aligned with other
in
pattern. Re-tighten wing nuts
when desired alignment is attained.
LOCKING LEVER
Fig. 2
1 For adjustable units, releasing
Locking Lever• allows
yoke to pivot from O to 35 degrees (Modules 142, 144,
and 146. 0 to 25 degrees for module 248). Re-engage
lever when desired angle is obtained.
2 Releasing "Rotation Disk Locking Lever• allows rotation
disk to rotate 360 degrees. Re-engage lever when
desired position is obtained.
3 To
from downlight to adjustable position, remove
downlight locking screw.
Rail
1-1 /2" channel
1 • channel
1 /2" conduit
Notes:
Installation by a licensed electrician only. Make sure power is off.
Building wires must be in compliance with local codes.
2 Rails are not supplied unless ordered. They come in two sizes
26" and 52". Contact the factory. Available immediately.
3 Fixture must be above ceiling before closing in.
Installation
Fasten rail supports to internal adjustment brackets on housing.
rails by gently squeezing wings of rail
together to ease passage of rails. Do not squeeze too hard or
the rail supports will take a set. When pressure is released, the
rail support will lock onto rails. (See Fig. 3)
2 Remove proper knockouts from junction box and attach connectors.
3 If alignment of square
is required, with trim removed, loosen
(2) wing nuts. Align aperture. Tighten wing nuts. {See Fig. 1)
4 Using the aperture as a template, mark tile for the aperture hole.
5 Cut hole in tile for a snug
around the
6 Adjust
so
is
with
tile face or 1 /16"
above. Do not allow aperture edge below tile face or more than
1 /16" above. Tighten rails to ceiling grid permanently. {See Fig. 7)
Wiring
1 Attach conduit or
to junction box. Make all splices.
2 Fixture must be grounded with green
screw or grounding wire provided.
Installation of LED Module Assembly:
Downlight Position.
{See Fig. 4)
Fixtures are pre-set at the factory in the downlight position per order.
Push in LED wire plug into pin plug in driver plate.
3 Engage LED module bracket into yoke until springs engage into slots.
4 When required, yoke may be rotated horizontally. {See
. 2)
5 To remove, unplug module. Depress spring. Pull module gently
form yoke {See
6).
Installation of LED Module Assembly:
Adjustable Position.
{See Fig. 4)
Place yoke in vertical position.
Push in LED wire plug into pin plug in driver plate.
3 Engage LED module bracket into yoke until springs engage into slots.
4 Adjust vertical and horizontal positions as desired. Lock in place with
locking levers {See Fig. 2).
5 To remove, unplug module. Depress spring. Pull module gently from
yoke {See
5).
Installation of Trim.
(See Fig. 4)
1 Squeeze springs on either side of trim and attach safe
chain.
2 Insert trim into aperture until
with ceiling on all s,des.
Access to Junction Box:
{See Fig. 1)
Remove trim (
d
isconnect safety chain) and LED module inside yoke,
release wire plug remove inner junction box cover.
Quality Control
Every
is made to assure that our products reach the job
in perfect condition. We welcome your comments.
Versen Company may change construction periodically without
notice as part of its program for product improvement.
1/2" bar
1• bar
1/2" - 1 • angle
Supports accept many types of roils. Job site scrap may be used.
KV3547 Union mode IBEW.
