background image

15

ENG 

Index

Page

Description of the appliance           

15

Instructions for use                

15

Programming timer

15

Cleaning and maintenance                   16

Problem solving                                   16

Sizes and specifications     

17

Accessories supplied                   

18

Installation                               

18

Active charcoal filters

18

A

An electronic programmer device with
TOUCH CONTROL technology to
control speed, light, programming and
power indicators in use as well as filter
saturation.

B

Metal filters.

C

Lamp with two bulbs - 20 W (G-4).

D, E

Vertically adjustable tubecovers.

Switch on the extractor fan a few minutes
before you start to cook in order to ensure that
a steady air flow has been established before
fumes appear.
Allow the extractor fan to run for several
minutes after you have finished cooking
(between 3 to 5 minutes) in order to expel all
the grease from the outlet duct. This prevents
the return of grease, smoke and smells.

Proceed as follows:
1) Turn the kitchen hood on and choose the

required speed. Press "timer". Suction
indicators 1, 2  and 3 will  start to flash.

2) Select the required time by pressing the

increase and decrease speed selectors.
There is a variation of 10 in 10 minutes.
(Min.= 10 min.; Max.= 30 min.)

3) Once the required time has been selected,

press "timer" again to memorise the
program. The speed indicator in use will
start to flash.

4) Intensive suction cannot be programmed

as it has a set length of 10 minutes.

Clean the filters when the saturation indicator lights
up. (See page 16, Filter cleaning section).
Once you have cleaned the filters, and with the
hood turned off,  press the increase and decrease
speed buttons at the same time for 3 seconds and
the indicator will switch itself off.

Instructions for use

Description  of the appliance

Programming timer

You may control the kitchen hood by
operating the controls as shown in the
diagram.

Minimum speed

Medium speed

Maximum speed

Extra fan

Filter saturation
indicators

Timer

Reduce speed

Increase speed

On-Off

Power indicator

Filter saturation  indicators

Manual KDT.qxd  17/06/2004  13:47  Page 15

Summary of Contents for KD 9475.0 E








Reviews: