Kubota Z723 Operator'S Manual Download

Page: 80 / 95

PERIODIC SERVICE

ENGLISH

Tighten the bolts of the blades from 103 to 118 N-m
(76 to 87 lbf-ft) of torque.

The blade bolts have Right hand threads. Turn them
counterclockwise to loosen.

To prolong the service life of the blades, reposition
them as shown in the figure below periodically.

Mower Belt Replacement

1. Remove the mower deck from the machine according

to the procedure "DISMOUNTING THE MOWER
DECK".

2. Remove the left and right hand shield from the mower

deck.

3. Remove the belt.
4. To install a new belt, reverse the above procedure.

Tighten the tension pulley bolt securely 77.6 to 90.2 N-
m (8.0 to 9.2 kgf-m, 57.1 to 66.5 lbf-ft).

(1) LH blade
(2) Center blade
(3) RH blade

(1) Tension pulley
(2) PTO clutch pulley
(3) Mower belt
(4) Bolt
(5) Shield

Summary of Contents for Z723
































































































Search results

Summary of Contents for Z723

Reviews:

Related manuals for Z723

Brands by name

Popular brands

Kubota Z723, Operator'S Manual

Search results

Summary of Contents for Z723

Reviews:

Related manuals for Z723

Brands by name

Popular brands