Kubota Z723 Operator'S Manual Download | Manualshive

Page: 70 / 95

background image

53

PERIODIC SERVICE

ENGLISH

B

Cleaning Engine Cooling Areas

The engine cooling areas should be cleaned every 100
hours operation or every 1 year, whichever comes first.

To avoid serious injury:

A

Make sure engine is cool to the touch before
removing shrouds.

A

Always shield eyes and face from air deposits
and objects.

1. Remove outer fan guard by removing its 3 mounting

bolts.

2. Remove inner fan guard by removing its 4 mounting

bolts.

3. Remove oil cooler by removing its 2 mounting bolts.
4. Remove fuel pump by removing its 2 mounting bolts.
5. Unplug engine wire harness from voltage regulator.
6. Remove green grounding bolt from voltage regulator.
7. Remove breather filter by removing its 2 mounting

bolts.

8. Remove blower cover by removing its 5 remaining

mounting bolts.

9. Clean all areas that were previously covered by the

blower cover with compressed air. Remove all dust,
dirt, and debris.

10.Reinstall all parts in the reverse order of the above

procedure.

(1) Outer Fan Guard and bolts
(2) Inner Fan Guard and bolts
(3) Oil Cooler
(4) Fuel Pump
(5) Voltage Regulator and Grounding Bolt
(6) Blower cover

(7) Breather Filter

«
...
68
69
70
71
72
...
»

Summary of Contents for Z723
































































































Reviews:

No comments

Related manuals for Z723

Brand: Gardenline Pages: 36

Brand: Oleo-Mac Pages: 332

Brand: Baroness Pages: 87

TZ51SF-BS625EXi

Brand: MADER Pages: 67

Brand: Toro Pages: 52

ULTRAVAC BAGGER

Brand: Exmark Pages: 19

Brand: Bestgreen Pages: 10

Brand: Lux Tools Pages: 148

Sportsman Forest 800

Brand: Cub Cadet Pages: 24

Z-Force S Commercial 60

Brand: Cub Cadet Pages: 40

Brand: Exmark Pages: 56

Laser Z LZS29PKA604

Brand: Exmark Pages: 64

Brand: Kubota Pages: 102

Brand: Nax Power Products Pages: 32

Brand: NAX Pages: 32

Brand: MTD Pages: 40

Brand: SHARKS Pages: 49

Brand: Scheppach Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands