Kubota WSM L3540-II Workshop Manual Download Page 51 | Manualshive

Page: 51 / 672

background image

GENERAL

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

G-29

Adjusting Fan Belt Tension

WARNING

• Be sure to stop the engine before checking fan belt tension.

1. Stop the engine and remove the key.
2. Apply moderate thumb pressure to belt between pulleys.
3. If tension is incorrect, loosen the alternator mounting bolts and

using a lever placed between the alternator and the engine
block, pull the alternator out until the deflection of the belt falls
within the factory specifications.

4. Replace fan belt if it is damaged.

9Y1211167GEG0035US0

Checking Fuel Line

1. Check to see that all line and hose clamp are tight and not

damaged.

2. If hoses and clamps are found worn or damaged, replace or

repair them at once.

NOTE

• If the fuel line is removed, be sure to properly bleed the fuel

system. (See page G-43.)

9Y1211167GEG0036US0

Fan belt tension

Factory specification

A deflection of between
7.0 to 9.0 mm (0.28 to 0.35
in.) when the belt is
pressed in the middle of
the span.

(1) Alternator Mounting Bolt

A : Check the belt tension
B : To Tighten

(1) Fuel Hose

(2) Clamp

KiSC issued 02, 2015 A

«
...
49
50
51
52
53
...
»

Summary of Contents for WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WSM L3540-II

Brand: Kellfri Pages: 32

Marathon RAMJET Signature J-250SC

Brand: Dover Pages: 47

Brand: WALTERSCHEID Pages: 20

Brand: SaMASZ Pages: 42

TRASH GUARD PLUS

Brand: ACF Pages: 2

Brand: SaMASZ Pages: 29

Brand: NEFF Pages: 12

Tiger TC-030-60

Brand: Taylor-Dunn Pages: 186

Brand: Yanmar Pages: 164

Brand: Terramite Pages: 128

Brand: IKEA Pages: 36

Brand: Digga Pages: 16

Brand: Belarus Pages: 381

Brand: Agri-Fab Pages: 24

PowerSafe 710 PS

Brand: BCS Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands