Home
/
Kubota
/
WSM L3540-II
/
Workshop Manual

Kubota WSM L3540-II, Workshop Manual, Page: 385 / 672

Share

Page: 385 / 672

Kubota WSM L3540-II Workshop Manual Download Page 385

BRAKES

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

5-M2

2. OPERATION

The brakes are provided on the power transmitting shafts (brake shafts (8)) through which power is transmitted

to the final reduction system. The brakes are incorporated in the brake case (1) filled with transmission oil. They are
designed to brake when the brake discs (2), spline-coupled and rotating with the brake shaft, are pressed against the
brake case by cam plate (3) with the cam mechanism incorporating steel balls (4). For greater braking force, two brake
discs are provided respectively, and the plate (6) fixed to the brake case are arranged between the brake discs.



During Braking

When the brake pedal is pressed, the force causes the brake cam lever (5) to move in the direction of allow

through the brake rod. At the same time, the brake cam (7) spline-couples with the brake cam lever also moves. Due
to this force, cam plate (3) moves in the direction of arrow. Since the steel balls (4) are set in the grooves of differential
case, cam plate (3) is pushed out against the brake discs (2), causing braking with the friction force created.

9Y1211167BRM0002US0

(1) Brake Case
(2) Brake Disc

(3) Cam Plate
(4) Steel Ball

(5) Brake Cam Lever
(6) Plate

(7) Brake Cam
(8) Brake Shaft

KiSC issued 02, 2015 A

«
...
383
384
385
386
387
...
»

Summary of Contents for WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments