Kubota RT120Q Operator'S Manual Download Page 66

Page: 66 / 219

RT120Q Operator’s Manual

Controls - 65

Backhoe Console

Remote throttle enable

To enable remote throttle
control, press top.

To disable remote throttle
control, press bottom.

This switch must be returned to the
OFF position for normal throttle
control at tractor.

Work light switch

To turn on, press right.

To turn off, press left.

Swing lock pin

To lock:

•

Engage stow lock.

•

Insert swing lock pin into
hole (1).

To release:

•

Remove pin and store in
hole (2).

•

Release stow lock.

This pin locks boom from swinging
during transport.

NOTICE: Do not

store pin in holes

marked with an “X.” Backhoe could
swing and destroy pin.

Remote ground drive
control

To move tractor forward,
push.

To move tractor backward,
pull.

NOTICE:

•

This control is disabled if tractor
seat is occupied.

•

Tractor must be in low speed for
remote ground drive to function.

•

Ensure that backfill blade, if
equipped, and stabilizers are
raised before operating this
control.

•

Do not move more than 30’ (10
m) at a time.

Item

Description

Notes

c00ic030w.eps

c00ic216h.eps

Summary of Contents for RT120Q




























































































































































































































Search results

Summary of Contents for RT120Q

Reviews:

Related manuals for RT120Q

Brands by name

Popular brands

Kubota RT120Q, Operator'S Manual

Search results

Summary of Contents for RT120Q

Reviews:

Related manuals for RT120Q

Brands by name

Popular brands