Kubota RT120Q Operator'S Manual Download Page 137

Page: 137 / 219

Drill - 136

RT120Q Operator’s Manual

Operate

Remove Rod

If the length of rod outside the bore reaches 30’ (9 m), ask a helper to remove rod sections as needed.

Remove Rod Section

Stop rotation of drilling attachment.

Shut down tractor. See page 87 for proper shutdown procedures.

Disconnect and remove appropriate rod section with special tool (p/n 351-272). See “Disassemble Drill
String” on page 138.

Rotating shaft will cause death or serious injury. Stay

away.

To help avoid injury:

•

Only access drill string with hands when tractor is shut down.

•

Always remove second rod (as shown). Leave first rod section attached to drilling attachment.

t48om060w.eps

Summary of Contents for RT120Q




























































































































































































































Search results

Summary of Contents for RT120Q

Reviews:

Related manuals for RT120Q

Brands by name

Popular brands

Kubota RT120Q, Operator'S Manual

Search results

Summary of Contents for RT120Q

Reviews:

Related manuals for RT120Q

Brands by name

Popular brands