Kubota RT120Q Operator'S Manual Download Page 112 | Manualshive

Page: 112 / 219

background image

RT120Q Operator’s Manual

Plow - 111

Operate

Operate

1.

If equipped with combo, ensure that the trench/plow switch is in the plow position.

2.

Move ground drive hand control forward to plowing speed and lower plow blade into ground.

3.

Move plow lift control to float.

4.

Move plow swing control to float.

5.

Increase engine speed to full throttle.

6.

Move attachment speed/direction control forward to start plow vibration. PLOW WILL VIBRATE.

7.

Reduce attachment speed to a point with the least tractor vibration and the highest ground drive speed
possible without track slippage. Adjust vibrator speed if ROPS vibrates excessively.

8.

Check cable for damage during plowing.

Crushing weight could cause death or serious injury. Stay

away.

Electric shock will cause death or serious injury. Stay

away.

274-049

To help avoid injury:

Expose lines by hand before digging. Cutting high voltage cable can cause

electrocution

Read operator’s manual. Follow safety rules and know

how to use all controls. Your safety is at stake.

273-475

NOTICE:

•

Lower plow into ground before moving plow lift control or plow swing control to float.

•

Do NOT move ground drive to reverse with plow blade in the ground.

NOTICE:

Do not operate vibrator unless plow is in the ground.

«
...
110
111
112
113
114
...
»

Summary of Contents for RT120Q




























































































































































































































Reviews:

No comments

Related manuals for RT120Q

Brand: Hagie Pages: 149

Brand: Kverneland Pages: 74

UpFront STS 10T

Brand: Hagie Pages: 93

Brand: Amica Pages: 76

Brand: MTD Pages: 28

Brand: MTD Pages: 28

Brand: MTD Pages: 36

Brand: New Holland Pages: 41

Brand: WALTERSCHEID Pages: 16

Brand: Komatsu Pages: 8

Brand: CAMSO Pages: 106

Brand: Kellfri Pages: 16

Brand: Cub Cadet Pages: 289

MONOGRAM ZCG3300 WW

Brand: GE Pages: 16

Brand: Ariens Pages: 21

Brand: Hagie Pages: 127

Brand: Worksaver Pages: 31

Brand: Peco Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands