Kubota RT120Q Operator'S Manual Download Page 110

Page: 110 / 219

RT120Q Operator’s Manual

Plow - 109

Set Up

Position Tractor

Fasten and adjust seat belt.

Start tractor. See page 84 for start-up procedures.

Drive to starting point. Move in line with planned trench. See “Drive” on page 85.

Set parking brake and verify parking brake indicator is on.

Lower backfill blade, if equipped.

If equipped with combo, set trench/plow switch to the plow position.

Lower plow to starting point of trench.

Turn ignition switch to STOP.

Attach Product

Pull Product

Insert material into pulling grip.

Tape grip with duct tape.

IMPORTANT:

If material must be at a constant depth, dig starting and target trenches.

Summary of Contents for RT120Q




























































































































































































































Search results

Summary of Contents for RT120Q

Reviews:

Related manuals for RT120Q

Brands by name

Popular brands

Kubota RT120Q, Operator'S Manual

Search results

Summary of Contents for RT120Q

Reviews:

Related manuals for RT120Q

Brands by name

Popular brands