Kubota RT120Q Operator'S Manual Download Page 109

Page: 109 / 219

Plow - 108

RT120Q Operator’s Manual

Set Up

EMERGENCY SHUTDOWN -

Turn ignition switch to STOP.

Crushing weight could cause death or serious injury. Stay

away.

To help avoid injury:

Keep everyone at least 10’ (3 m) from machine, attachments, and their range of

movement.

Jobsite hazards could cause death or serious injury. Use

correct equipment and work methods. Use and maintain proper safety
equipment.

To help avoid injury:

Comply with all utility notification regulations before digging or drilling.

Read operator’s manual. Follow safety rules and know

how to use all controls. Your safety is at stake.

273-475

To help avoid injury:

Use attachments or counterweights to make front and rear loads balance when all

attachments are raised. Contact your Ditch Witch

dealer about counterweighting for your equipment.

Summary of Contents for RT120Q




























































































































































































































Search results

Summary of Contents for RT120Q

Reviews:

Related manuals for RT120Q

Brands by name

Popular brands

Kubota RT120Q, Operator'S Manual

Search results

Summary of Contents for RT120Q

Reviews:

Related manuals for RT120Q

Brands by name

Popular brands