Kubota M7-132, Operator'S Manual

Page: 25 / 332

and injectors on engines with high pressure
common rail fuel system.
• To avoid hazardous high voltage, turn the key
switch to the “OFF” position if it is necessary to
check or repair the computer, harness or
connectors.
• During diesel particulate filter (hereinafter called
DPF) regenerating operations, exhaust gases and
exhaust filter components reach temperatures hot
enough to burn people, or ignite or melt common
materials.
• Keep the tractor away from people, animals or
structures which may be susceptible to harm or
damage from hot exhaust gases.
• To prevent fires, keep the DPF/SCR muffler and its
surroundings clear of anything flammable and keep
clean at all times (selective catalytic reduction -
hereinafter called SCR).
• To avoid fire hazard:
After use and pressure-washing, make sure there is
nothing flammable near the exhaust pipe. Grass or
twigs under the bonnet may cause fire.
• During regeneration, white exhaust gas may be
visible. Do not allow regeneration in a non-
ventilated space.
• During regeneration, do not leave the tractor.
• The improper disposal or burning of waste causes
environmental pollution and can be punishable by
your local laws and regulations.
– When draining fluids from the tractor, place a
container underneath the drain port.
– Do not pour waste onto the ground, down a
drain, or into any water source (such as rivers,
streams, lakes, marshes, seas and oceans).
– Waste products such as used oil, fuel, coolant,
hydraulic fluid, urea aqueous solution (DEF/
AdBlue
®
), refrigerant, solvent, filters, rubber,
batteries and harmful substances, can harm the
environment, people, pets and wildlife.
Please dispose properly.
See your local recycling centre or KUBOTA
Dealer to learn how to recycle or get rid of
waste products.
• Before servicing a tractor equipped with the front
suspension, be sure to lower the machine to the
lowest position.
• The front suspension hydraulic circuit is still under
high pressure after the engine has stopped. Do not
disconnect the pipes and/or hoses because you
may get injured by high-pressure oil. If pipes and/or
hoses are found worn or damaged, consult your
local KUBOTA Dealer for this service.
USING AUTO STEERING
SYSTEM
1. Intended use
The automatic steering system is designed to be
controlled by persons working in agriculture.
Any usage beyond recommendations is therefore
prohibited.
Kubota auto steering is not suitable for applications on
narrow dikes or steep hillsides, when danger of tractor
roll-over exists.
It should not be exposed to areas that are in danger of
explosions.
Never expose the unit or individual components to
chemicals such as: acids, lye, oils, lubricants or other
aggressive petro-chemical materials.
The manufacturer is not responsible for any damages
relating to contrary to the intended use.
The risk is the sole responsibility of the user.
The intended use also applies to recommended
operator regulations as well as service and
maintenance directions.
2. General advice
Please read this manual thoroughly.
This manual and safety labels may also be available in
other languages.
Check with your dealer or our internet website.
3. Responsibilities of the owner
Only persons who have read and understood the
complete manual should work with this system.
Only persons who are familiar with installation, service
and repair of the steering system, and also aware of
possible dangers in conjunction with the job, should
use the system.
Regional regulations for health protection and accident
prevention must be obeyed at all times and while
working with the system. Never use the system on
public roads or highways.
Any changes to the steering system which are not
authorized by the manufacturer, void any liability of the
manufacturer in the event of a malfunction.
If you do not understand any part of this manual and
need assistance please contact your dealer.
4. Demands on operating and
service personnel
Every person operating or servicing this system must
meet the following minimum requirements:
• He/she is physically capable of controlling the
machine.
SAFE OPERATION
M7132, M7152, M7172
19