background image

3

SPECIFICATIONS OF THE TRACTOR

SPECIFICATIONS OF THE TRACTOR

SPECIFICATION TABLE

Model

L47

M62

Engine

Model

V2403-CR-E4-TLB1

V2403-CR-TE4-TLB1

Type

Direct injection vertical, water-cooled, 4-cycle diesel

No. of cylinders

4

Bore and stroke

mm (in.)

87 x 102.4 (3.4 x 4.0)

PTO power (factory observed)

kW (HP)

24.6 (33)

34.3 (46)

Net power (without fan)

kW (HP)

34.6 (46.4)

46.3 (62.1) *

Total displacement

L (cu. in.)

2.434 (148.5)

Rated revolution

rpm

2700

Low idling revolution

rpm

950 to 1000

Battery

12V, RC: 90 min, CCA: 

550 A

12V, RC: 115 min, CCA: 

650 A

Capacities

Fuel tank

L (U.S.gals.)

67 (17.7)

Engine crankcase (with filter)

L (U.S.qts.)

8.2 (8.7)

9.4 (9.9)

Engine coolant

L (U.S.qts.)

8.2 (8.7)

Transmission case

L (U.S.gals.)

46 (12.2)

Front axle case

L (U.S.qts.)

7.0 (7.4)

12.5 (13.2)

Tires

Front

27 x 10.5-15 R4

10-16.5 R4

Rear

15-19.5 R4

17.5L-24 R4

Dimensions

Min. ground clearance

mm (in.)

365 (14.4) at transmission  

case

350 (13.8) at transmission 

case

Tread

Front

mm (in.)

1165 (45.9)

1440 (56.7)

Rear

mm (in.)

1426 (56.1)

1462 (57.6)

Weight (with ROPS & FOPS, main frame)

kg (lbs.)

1988 (4383)

2264 (4991)

PTO shaft

Transmission case rear

Rear PTO

SAE 1-3/8, 6 Spline

Steering

Hydraulic power

Transmission

Hydrostatic transmission

(3 speeds)

Min. turning radius

m (feet)

2.8 (9.2)**

3.3 (10.8) **

Brake

Multiple wet disks operated by two foot pedals

which can be locked together.

Differential

Bevel gear

* Manufacturer's estimate
** with brake

The company reserves the right to change the specifications without notice.

Summary of Contents for L47TL
































































































































































Reviews: