Kubota G23 Workshop Manual Download Page 98

Page: 98 / 343

ENGINE

G23, G26, WSM

1-S16

(EU)

Checking Valve Clearance

IMPORTANT

• Valve clearance must be checked and adjusted when

engine is cold.

1. Remove the cylinder head cover and the glow plugs.
2. Align the

"1TC"

mark (1) on the flywheel and alignment mark (2)

on the rear end plate so that the No. 1 piston comes to the
compression top dead center.

3. Check the following valve clearance marked with "

" using a

feeler gauge.

4. If the clearance is not within the factory specifications, adjust

with the adjusting screw.

5. Then turn the flywheel 6.28 rad (360 °) and align the

"1TC"

mark (1) on the flywheel and alignment mark (2) on the rear end
plate so that the No.1 piston comes to the overlap position.

6. Check the following valve clearance "

" using a feeler gauge.

7. if the clearance is not with in the factory specifications, adjust

with the adjusting screw.

Valve clearance marked with "

" can be adjusted.

NOTE

• The sequence of cylinder numbers is given as No. 1, No. 2

and No. 3 starting from the gear case side.

• After adjusting the valve clearance, secure the adjusting

screw with the lock nut.

9Y1210294ENS0006US0

Adjustable cylinder location of

piston

Number of cylinder valve arrangement

Intake valve

Exhaust valve

No. 1

No. 2

No. 3

Intake and exhaust valve
clearance (cold)

Factory specification

0.145 to 0.185 mm
0.00571 to 0.0728 in.

(1)

1TC

Mark

(2) Alignment Mark

A : Gear Case Side

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands

Kubota G23, Workshop Manual

Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands