Kubota G23 Workshop Manual Download Page 36

Page: 36 / 343

GENERAL

G23, G26, WSM

G-18

(EU)

Checking and Cleaning Panel and Radiator Screen

CAUTION

To avoid personal injury :

• Be sure to stop the engine and remove the key before

removing the screen.

1. Check the panel screens to be sure they are clean from debris.
2. Detach the lower panel plate.

NOTE

• If the dust or chaff is accumulated in the battery

compartment, clean it thoroughly.

3. Detach the radiator screen, and then remove all the foreign

material.

IMPORTANT

• Panel and radiator screen must be clean from debris to

prevent engine from overheating and to allow good air
intake for air cleaner.

• Be sure to reinstall the panel on the pillar completely to

prevent the invasion of dust.

• Be sure to stop the engine to avoid personal injury and to

allow good air intake for air cleaner.

9Y1210294GEG0010US0

Checking Tyre Pressure

WARNING

To avoid personal injury :

• Do not attempt to mount a tyre on a rim. This should be

done by a qualified person with the proper equipment.

• Always maintain the correct tyre pressure.

Do not inflate tyres above the recommended pressure
shown in the Operator's Manual.

• Inflation pressure in front tyres rises quickly when using

compressed air.

CAUTION

Never operate machine with a loose rim, wheel, or axle.

• Whenever bolts are loosened, retighten to specified torque.
• Check all bolts frequently and keep them tightened.

Inflation Pressure

Though the inflation pressure is factory-set to the prescribed

level, it naturally drops slowly in the course of time. Thus, check it
everyday and inflate as necessary.

9Y1210294GEG0074US0

(1) Panel
(2) Knob
(3) Centre Pillar
(4) Radiator Screen

A : Detach

Tyre Sizes

Recommended Inflation

Max. Pressure

Front

16 × 7.50-8, Turf

120 kPa (1.2 kgf/cm

17.4 psi)

Rear

24 × 12.00-12, Turf

100 kPa (1.0 kgf/cm

14.5 psi)

(1) Ground

(A) Insufficient
(B) Normal
(C) Excessive

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands

Kubota G23, Workshop Manual

Search results

Summary of Contents for G23

Reviews:

Brands by name

Popular brands