manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 34

GENERAL

G23, G26, WSM

G-16

(EU)

7. CHECK AND MAINTENANCE

 CAUTION

• Be sure to check and service the machine on a level surface with the engine shut off and the parking brake

"ON" and implement lowered to the ground.

9Y1210294GEG0005US0

[1] DAILY CHECK

To prevent trouble from occurring, it is important to know the condition of the machine. Check it before starting.

 CAUTION

To avoid personal injury :

• Be sure to check and service the machine on a level surface with the engine shut off, the ley removed and

the parking brake securely set.

9Y1210294GEG0006US0

(1) Walking Around the Machine

1. Tyre pressure, wear and damage.
2. Oil and water leak.
3. Engine oil level.
4. Transmission fluid level.
5. Coolant level in the recovery tank.
6. Damage of machine body, tightness of all bolts and nuts.
7. Radiator screen.
8. Panel screen.
9. Brake free travel.
10. Fuel level.
11. Check air cleaner.

9Y1210294GEG0007US0

Checking Engine Oil Level

 CAUTION

To avoid personal injury :

• Be sure to stop the engine before checking the oil level.

1. Park the machine on a flat surface.
2. Check engine oil before starting the engine or 5 minutes or more

after the engine has stopped.

3. To check the oil level, draw out the dipstick, wipe it clean,

replace it, and draw it out again. Check to see that the oil level
lines between the two notches.
If the level is too low, add new oil to the prescribed level at the
oil inlet. (Refer to "LUBRICANTS, FUEL AND COOLANT" in this
section.)

IMPORTANT

• When using an oil of different maker or viscosity from the

previous one, remove all of the old oil and oil filter.
Never mix two different types of oil.

• If oil level is low, do not run the engine.

9Y1210294GEG0008US0

(1) Oil Inlet
(2) Dipstick

A : Oil level is acceptable within this 

range.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands