manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 335

GRASS COLLECTOR

G23, G26, WSM

8-S5

(EU)

[2] DISASSEMBLING GRASS COLLECTOR

(1) Disassembling Grass Collector (LD)

Dismounting Grass Collector

1. Park the machine on a level ground shut off the engine and

remove the key.

2. Turn the lock lever (2) to outside of the machine.
3. Slide the bag pins (4) into the hook (3).
4. Pull and turn the both L pins (1).
5. Tilt the grass collector forward, and them lock the both L pins

(1).

(When mounting)

• Shut off the engine.
• Move the grass collector control lever several times.
• Reverse the above dismounting procedure.

9Y1210294GCS0005US0

(1) L Pin
(2) Lock Lever
(3) Hook
(4) Bag Pin

A : "PULL"
B : "TURN"

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands