manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 304

ELECTRICAL SYSTEM

G23, G26, WSM

6-S26

(EU)

Magnet Switch

1. Remove the drive end frame (1) mounting screws.
2. Take out the overrunning clutch (2), ball (3), spring (4), gears

(5), rollers (6) and retainer (7).

(When reassembling)

• Apply grease to the gear teeth of the gears (5) and overrunning

clutch (2), and ball (3).

9Y1210294ELS0032US0

Plunger

1. Remove the end cover (1).
2. Take out the plunger (2).

WSM000001ELS0022US0

(2) Alternator

Alternator

1. Check the battery charging voltage while engine runs.
2. Check the increasing voltage when increasing the engine

revolution.

3. If the battery charging voltage does not increase, the alternator

is faulty.

4. Replace the alternator as an assembly.

9Y1210294ELS0033US0

[3] SERVICING

(1) Starter

Overrunning Clutch

1. Inspect the pinion for wear or damage.
2. If there is any defect, replace the overrunning clutch assembly.
3. Check that the pinion turns freely and smoothly in the

overrunning direction and does not slip in the cranking direction.

4. If the pinion slips or does not rotate in the both directions,

replace the overrunning clutch assembly.

WSM000001ELS0033US0

(1) Drive End Frame
(2) Overrunning Clutch
(3) Ball
(4) Spring

(5) Gear
(6) Roller
(7) Retainer

(1) End Cover

(2) Plunger

(1) Battery

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands