manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 296

ELECTRICAL SYSTEM

G23, G26, WSM

6-S18

(EU)

(14) Combination Switch

Combination Switch

1. Remove the meter panel, and disconnect the combination

switch connector.

2. Remove the combination switch (1) and perform the following

checks 

1)

 to 

8)

.

1) Connector Voltage

1. Connect the combination switch connector to the main wire

harness.

2. Measure the voltage with a voltmeter across the connector 

B1

terminal and chassis when the main switch is 

ON

 position.

3. If the voltage differs from the battery voltage, the wiring harness

and main switch is faulty.

2) Head Light Switch Continuity When Setting Switch at OFF
Position

1. Set the light switch to the 

OFF

 position.

2. Measure the resistance with an ohmmeter across the red /

yellow lead (1) to the orange lead (4), the red / yellow lead (1) to
the yellow lead (3).

3. If infinity is not indicated, the head light switch is faulty.

(1) Combination Switch
(2) Red / Yellow Lead
(3) Green Lead
(4) Black / Blue Lead
(5) Blue / White Lead

(6) Yellow Lead
(7) Orange Lead
(8) Red / White Lead
(9) Green / White Lead

Voltage

Main switch 
at 

"ON"

 

position

B1

 terminal 

– Chassis

Battery voltage

Resistance
(Switch at 

OFF

 

position)

Red / Yellow lead (1) – 
Orange lead (4)

Infinity

Red / Yellow lead (1) – 
Yellow lead (3)

(1) Red / Yellow Lead
(2) Blue / White Lead
(3) Yellow Lead
(4) Orange Lead
(5) Red / White Lead

A : Head Light "OFF" Position

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands