manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 294

ELECTRICAL SYSTEM

G23, G26, WSM

6-S16

(EU)

(12) Charging System

Battery Charging Current

1. After starting the engine, disconnect the battery positive cord

(+), and connect an ammeter and voltmeter. Then switch on all
electrical loads (such as head lights) and measure the charging
current.

NOTE

• Connect an ammeter only after starting the engine.
• When the electrical loads is considerably low or the battery

is fully charged, the specified reading may not be obtained.

9Y1210294ELS0020US0

(13) Alternator

Stator

1. Measure the resistance across each lead of the stator coil with

an ohmmeter.

2. If the measurement is not within factory specification, replace it.
3. Check the continuity across each stator coil lead and core with

an ohmmeter.

4. If infinity is not indicated, replace it.

WSM000001ELS0040US0

Rotor

1. Measure the resistance across the slip rings with an ohmmeter.
2. If the resistance is not the factory specification, replace it.
3. Check the continuity across the slip ring and core with an

ohmmeter.

4. If infinity is not indicated, replace it.

WSM000001ELS0041US0

Slip Ring

1. Check the slip ring for score.
2. If scored, correct with an emery paper or on a lathe.
3. Measure the O.D. of slip ring with vernier calipers.
4. If the measurement is less than the allowable limit, replace it.

WSM000001ELS0042US0

Factory specification

Current

14 to 15 A

Voltage

14 to 15 V

Alternator speed

5200 min

-1

 (rpm)

(1) Battery Positive Cord

Resistance

Factory specification

Less than 1.0 

Ω

Resistance

Factory specification

2.9 

Ω

Slip ring O.D.

Factory specification

14.4 mm
0.567 in.

Allowable limit

14.0 mm
0.551 in.

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands