manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 273

ELECTRICAL SYSTEM

G23, G26, WSM

6-M6

(EU)

[2] IC REGULATOR (3P CONNCTOR TYPE)

3P

 connector is connected to the IC regulator. 

3P

connector consists of three leads, Sb (Sky Blue) lead (1),
RY (Red / Yellow) lead (2), and WR (White / Red) lead
(3).

Sb (Sky Blue) lead (1) is a lead to transmit the plus

from the alternator to hour meter and tachometer. When
turning on the main switch to 

"ON"

 position, the hour

meter indicates operated hours.
While the engine runs, the tachometer indicates the
present engine revolutions.

RY (Red / Yellow) lead (2) is a lead to the main

switch.

WR (White / Red) lead (3) is a lead to the charge

lamp.

9Y1210294ELM0004US0

(1) Sb (Sky Blue) Lead
(2) RY (Red / Yellow) Lead
(3) WR (White / Red) Lead
(4) Alternator Assembly
(5) IC Regulator
(6) Load
(7) Load

A : To Hour Meter and 

Tachometer

B : To Main Switch "ON" 

Position

C : To Charge Lamp
D : To Battery

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands