manualshive.com logo in svg

Kubota G23, Workshop Manual

Share
Download
Kubota G23 Workshop Manual Download Page 198

TRANSAXLE

G23, G26, WSM

2-S37

(EU)

Hydraulic PTO Clutch 4

1. Press the brake spring (6) by using the PTO clutch spring

compression tool (2).

2. Remove the cir-clip (4) by a snap ring plier.
3. Disassemble the PTO clutch.

(When reassembling)

• Do not damage the ring seals.

9Y1210294TXS0055US0

[4] SERVICING

(1) Hydrostatic Transmission

Centre Section

1. Check the centre section surface (1) for scratches or wear.
2. If deep scratch or excessive wear is found, replace the

hydrostatic transmission assembly.

9Y1210294TXS0036US0

(1) Cir-clip
(2) PTO Clutch Spring Compression 

Tool

(3) Clutch Case
(4) Nut
(5) Washer

(6) Brake Spring
(7) Clutch Piston
(8) Ring Seal
(9) Brake Plate
(10) Brake Disk
(11) Ring Seal

(1) Centre Section Surface

KiSC issued 08, 2009 A

Summary of Contents for G23
























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands