Kubota B1220 Workshop Manual Download

Page: 323 / 343

ELECTRICAL SYSTEM

B1220, B1620, B1820, WSM

9-S26

(EU)

(10) Starter

Motor Test

CAUTION

• Secure the starter to prevent it from jumping up and down

while testing the motor.

1. Disconnect the battery negative cable from the battery.
2. Disconnect the battery positive cable and the leads form the

starter

terminal.

3. Remove the starter from the engine.
4. Disconnect the connecting lead (2) from the starter

terminal

(1).

5. Connect a jumper lead from the connecting lead (2) to the

battery positive terminal post.

6. Connect a jumper lead momentarily between the starter motor

housing and the battery negative terminal post.

7. If the motor does not run, check the motor.

9Y1210272ELS0021US0

Magnet Switch Test

1. Disconnect the battery negative cable from the battery.
2. Disconnect the battery positive cable and the leads from the

starter

terminal.

3. Remove the starter from the engine.
4. Disconnect the connecting lead (3) from the starter

terminal

(2).

5. Connect a jumper lead from the starter

terminal (1) to the

battery positive terminal post.

6. Connect a jumper lead momentarily between the starter

terminal (2) and the battery negative terminal post.

7. If the pinion gear does not pop out, check the magnetic switch.

NOTE

• This test should be carried out for a short time, about 3 to

5 seconds.

9Y1210272ELS0022US0

(11) AC Dynamo [B1220]

Dynamo No-load Voltage

1. Disconnect the lead wires from the dynamo.
2. Start the engine, and check the generating voltage of the

dynamo.

9Y1210272ELS0023US0

(1)

Terminal

(2) Connecting Lead

(1)

Terminal

(2)

Terminal

(3) Connecting Lead

Voltage

Factory specification

14 to 15 V (at engine idling
speed)

36 to 39 V (at engine high
speed)

KiSC issued 07, 2011 A

Summary of Contents for B1220
























































































































































































































































































































































Search results

Summary of Contents for B1220

Reviews:

Related manuals for B1220

Brands by name

Popular brands

Kubota B1220, Workshop Manual

Search results

Summary of Contents for B1220

Reviews:

Related manuals for B1220

Brands by name

Popular brands