manualshive.com logo in svg

KTM Freeride E-XC 2019, Setup Instructions, Page: 39 / 44

Share
Download
KTM Freeride E-XC 2019 Setup Instructions Download Page 39

WORK 4

37

4.27

Ascertaining that the discharge plug is de-energized

Warning

Risk of injury

 

The measuring points could be live.

–

Use personal protective clothing and comply with the safety measures.

Condition

The KTM PowerPack has been removed.

309699-10

Main work

–

Prepare the special tool for measurement.

AVL DITEST HV Safety 2000 (70029068000)

–

Start software

HV Safety

.

–

Select

"Zero-potential"

.

–

Follow the instructions in the

HV Safety

Owner's Manual.

Finishing work

–

Mount the protection cap.

(

p. 19)

4.28

Performing an equipotential bonding check (KTM PowerPack installed)

Warning

Risk of injury

 

The measuring points could be live.

–

Use personal protective clothing and comply with the safety measures.

Condition

The KTM PowerPack has been removed.

309699-10

–

Prepare the special tool for measurement.

AVL DITEST HV Safety 2000 (70029068000)

–

Start software

HV Safety

.

–

Select

"Equipotential bonding check"

.

–

Follow the instructions in the

HV Safety

Owner's Manual.

4.29

Performing an equipotential bonding check (KTM PowerPack installed)

Warning

Risk of injury

 

The measuring points could be live.

–

Use personal protective clothing and comply with the safety measures.

Condition

The KTM PowerPack has been removed.

Summary of Contents for Freeride E-XC 2019













































Reviews:

No comments