background image

3 WORK

27

Preparatory work
(All EXC models)

Press and hold the kill switch

while the engine is idling

until the engine stops.

(250 XC

W TPI US)

Press and hold the kill switch

while the engine is idling

until the engine stops.

Remove the seat. (

p. 19)

F00138-10

Main work

Warning

Risk of injury

Batteries contain harmful substances.

Keep batteries out of the reach of children.

Keep sparks and open flames away from the batter-
ies.

Only charge batteries in well-ventilated rooms.

Maintain a minimum clearance from inflammable
materials when charging batteries.
Minimum clearance

1 m (3 ft)

Do not charge deeply discharged batteries if charge
is already below the minimum voltage.
Minimum voltage before
the start of the charge

9 V

Dispose of batteries with less than the minimum
voltage correctly.

Disconnect negative cable

1

from the battery.

Pull back positive terminal cover

2

and disconnect the posi-

tive cable from the battery.

Remove screw

3

.

Pull holding bracket

4

forward and remove battery toward

the top.

3.12

Recharging the battery

Warning

Risk of injury

Batteries contain harmful substances.

Keep batteries out of the reach of children.

Keep sparks and open flames away from the batteries.

Only charge batteries in well-ventilated rooms.

Maintain a minimum clearance from inflammable materials when charging batteries.
Minimum clearance

1 m (3 ft)

Do not charge deeply discharged batteries if charge is already below the minimum voltage.
Minimum voltage before the start of the charge

9 V

Dispose of batteries with less than the minimum voltage correctly.

Summary of Contents for F7303R2














































Reviews: