KTM 50 SX Mini Repair Manual Download

Page: 121 / 159

38/LUBRICATION SYSTEM

119

Danger

Danger of poisoning

Exhaust gases are poisonous and inhaling them may

result in unconsciousness and/or death.

–

When running the engine, always make sure there is sufficient ventila-
tion, and do not start or run the engine in an enclosed space without an
effective exhaust extraction system.

–

Start the engine and check that it is oil-tight.

21.6

Filling up with oil (50 SX Mini)

Warning

Engine failure

If the vehicle is run without 2-stroke oil in the tank, the result is engine failure.

–

The oil tank must always be filled up to the

MIN

mark.

–

Switch off the engine.

–

Open the oil tank cap.

700518-01

–

Fill the oil tank at least up to the

MIN

mark



Guideline

MIN

mark

Sufficient for a single tank filling

Oil tank contents
ca.

0.2 l (0.2 qt.)

2-stroke engine oil (

p. 142)

–

Close the oil tank cap.

21.7

Bleeding the oil pump (50 SX Mini)

Condition

The fuel tank has been removed.

300650-10

–

Pull off oil line



300652-10

–

Fill the oil line with a syringe.

2-stroke engine oil (

p. 142)

300650-10

–

Connect oil line



PartShark.com

877-999-5686

Summary of Contents for 50 SX Mini
































































































































































Search results

Summary of Contents for 50 SX Mini

Reviews:

Related manuals for 50 SX Mini

Brands by name

Popular brands

KTM 50 SX Mini, Repair Manual

Search results

Summary of Contents for 50 SX Mini

Reviews:

Related manuals for 50 SX Mini

Brands by name

Popular brands