KTM 2010 690 SMC EU Setup Instructions Download

Page: 13 / 17

WORK

3.13

Setting the clock

Condition

The motorcycle is stationary.

400838-01

–

Switch on the ignition by turning the ignition key to position

–

Press the

MODE

button repeatedly until the

ODO

mode is active.

–

Keep the

MODE

button and the

SET

button pressed simultaneously.

The time display begins to flash.

–

Press the

MODE

button to set the hour.

–

Press the

SET

button to set the minute.

–

Keep the

MODE

button and the

SET

button pressed simultaneously.

The time is set.

3.14

Setting kilometers or miles

Info

If you change the unit, the value

ODO

is retained and converted accordingly.

Making the setting according to the country.

Condition

The motorcycle is stationary.

400839-01

–

Switch on the ignition by turning the ignition key to position

–

Press the

MODE

button repeatedly until the

ODO

mode is active.

–

Keep the

MODE

button pressed until the display mode changes from

km/h

mph

from

mph

km/h

Summary of Contents for 2010 690 SMC EU


















Search results

Summary of Contents for 2010 690 SMC EU

Reviews:

Related manuals for 2010 690 SMC EU

Brands by name

Popular brands

KTM 2010 690 SMC EU, Setup Instructions

Search results

Summary of Contents for 2010 690 SMC EU

Reviews:

Related manuals for 2010 690 SMC EU

Brands by name

Popular brands