KTC COMPACK 2 ECO Operation And Maintenance Manual Download Page 47 | Manualshive

Page: 47 / 63

background image

CONFIDENTIAL - This document is the property of K.T.C. S.r.l. and cannot be reproduced or issued to third parties without written

authorization. K.T.C. S.r.l. shall safeguard its rights to the full extent of the law.

OPERATION AND INSTALLATION MANUAL
COD. 091114 – COMPACK 2 ECO / SPECIAL - REV. 08 - DATE 10/2020

page

47

of

63

9.6

DESCRIPTION OF THE CONTROL DEVICES (ECO VERSION)

ECO VERSION

ATTENTION
The manual control of the compressor can only be managed by the GENERAL

compressor start-up and shutdown switch.

ATTENTION
After an emergency stop caused by high oil or engine temperature, press the green

button I to restart the compressor.

ATTENTION
Before carrying out any type of intervention in the compressor, make sure that the

machine is off (ignition light off) and with the system at ambient pressure (see
manometer).

ATTENTION
The compressor's working hours are visible in the COUNTER.

COUNTER

MANOMETER

MAIN SWITCH

IGNITION
LIGHT

«
...
45
46
47
48
49
...
»

Summary of Contents for COMPACK 2 ECO
































































Reviews:

No comments

Related manuals for COMPACK 2 ECO

Brand: U.S. General Pages: 19

Brand: EUROPRO Pages: 16

Brand: Ingersoll-Rand Pages: 43

Brand: Ingersoll-Rand Pages: 71

Brand: Ridetech Pages: 12

Brand: PRESONUS Pages: 1

Brand: Will Burt Pages: 7

Brand: Gude Pages: 64

Brand: Atlas Copco Pages: 74

Brand: WERTHER INTERNATIONAL Pages: 13

Brand: GEA Pages: 30

Brand: RIX Pages: 21

Brand: XTM Pages: 2

Brand: Parkside Pages: 105

Brand: Quincy Compressor Pages: 56

Brand: Quincy Compressor Pages: 44

Brand: Campbell Hausfeld Pages: 2

Brand: GEA Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands