Ksenia KSI5008000.301 Installation Manual Download Page 1

code R30049.110en                                                                                                                                                                           www.kseniasecurity.com
ed.12/2021

micro poli

WLS multifunction magnetic
contact

Installation guide

INTRODUCTION

micro poli 

is a wireless multifunction sensor, in compliance with the wireless bidirectional 868 MHz 

protocol used by Ksenia Security. Inside a very small case characterized by an essential and minimalist 
design, 

micro poli 

is much more than a simple magnetic contact.

micro poli 

is:

an 

anti-masking magnetic contact

 to detect the opening of doors and windows; 

an 

inertial sensor

 to detect the vibrations of increasing intensity up to the breaking of glass/windows;

able to measure the inclination 

of the window/door frame it protects, it allows the management of any 

type of window opening (casement window, tilt and turn window, bottom hung windows, etc.) which it 
would otherwise be impossible with only the magnetic contact.

As anti-masking magnetic contact

 with two REEDs (long side/short side) inside the transmitter, it is 

extremely suitable for any type of door or window frames thanks to the installation position of the magnet 
with respect to the transmitter. It is also possible to activate only one REED to detect the opening of the 
window, according to the type of installation; masking attempts by applying a more powerful magnet 
outside the frame can be detected, in this case it triggers a masking signal while the opening of the contact 
triggers a Zone Alarm.

As inertial sensor

, thanks to the 3-Axis accelerometer based on MEMs technology, when the vibration 

exceeds the programmed sensitivity threshold, it triggers an alarm.

As advanced sensor

, thanks to the 3-Axis accelerometer, it measures the angle of inclination of the window 

within which the zone is considered on idle and beyond which it triggers an alarm.

KSI5008000.301  - white
KSI5008000.302  - black
KSI5008000.304  - brown

Summary of Contents for KSI5008000.301












Reviews: