manualshive.com logo in svg

KSB UPAchrom CC, Installation & Operating Manual

Share
Download
KSB UPAchrom CC Installation & Operating Manual Download Page 18

5 Installation at Site

18 of 44

UPAchrom

5 Installation at Site

5.1 Checks to be carried out prior to installation

5.1.1 Checking the motor fill

The pump set can be installed directly in a vertical or horizontal 

3)

 position without

any further preparations. The motors are filled at the factory with water and
antifreeze agent. The loss of a few drops of liquid fill will not impair the motor
function as the motor will self-prime with clean well water after it has been installed.
If larger quantities of leakage are suspected, contact the manufacturer!

5.1.2 Checking the installation position

 WARNING

Impermissible installation position

Damage to the machine! Damage to the bearings!

▷

For angled installation, always install the pump set with a rising slope towards
the discharge side.

The pump set can be installed in a vertical or, depending on the number of stages,
also in an angled or horizontal position.
The pump set must not be installed with the pump as the lowest point.

A

B

Fig. 3: 

Installation position

A

Permitted

B

Not permitted

Particularities of horizontal installation

Check the following criteria before installing the pump set in a horizontal position:

▪

Has the pump set been ordered for horizontal installation?

▪

Has a sufficiently dimensioned cooling shroud or cooling hood been provided?

Pump sets originally selected for vertical installation must not be installed
horizontally. 
Only pump sets equipped with cooling shrouds may be installed horizontally.

5.1.3 Connecting the cables

 DANGER

Unqualified personnel connecting extension cables

Installation in a well - electric shock!

▷

The extension cable must be connected by a professional electrician only.

▷

The cable ends must be dry and clean.

3)

Only if equipped with a cooling shroud

Summary of Contents for UPAchrom CC













































Reviews:

No comments

Brands by name

Popular brands

Load more brands