KSB UPA Installation & Operating Manual Download Page 24

Page: 24 / 98

4 Description of the Pump (Set)

24 of 98

UPA / UPA S

3400.86/17-EN

4.8 Scope of supply

Depending on the model, the following items are included in the scope of supply:

▪

Pump set with motor lead

Optional:

▪

Pump and/or motor as individual units

▪

Power cable

– Connected or supplied but not fitted

▪

Equipment for filling the motor

▪

Separate name plate

▪

Separate warning sticker

(

Section 3.5, Page 16)

Optional accessories:

▪

Cable connector

▪

Cable clips

▪

Cooling shroud, suction shroud or pressure shroud

▪

Pedestals

▪

Electrical protection equipment

▪

Automatic control units

NOTE

A separate name plate is included in the scope of supply.
This name plate must be attached in a clearly visible position outside the place of
installation, e.g. at the control panel, pipeline or mounting bracket.

4.9 Dimensions and weights

For dimensions and weights refer to the data sheet of the pump (set).

Only for UMA 300, 14D submersible motors

Only for UMA-S 150, UMA-S 200, UMA-S 250 submersible motors

Summary of Contents for UPA



































































































Search results

Summary of Contents for UPA

Reviews:

Related manuals for UPA

Brands by name

Popular brands

KSB UPA, Installation & Operating Manual

Search results

Summary of Contents for UPA

Reviews:

Related manuals for UPA

Brands by name

Popular brands