manualshive.com logo in svg

KSB Hya-Rain, Installation & Operating Manual

Share
Download
KSB Hya-Rain Installation & Operating Manual Download Page 19

5 Installation at Site

19 of 64

Hya-Rain/Hya-Rain N

5.4 Connecting the piping

5.4.1 Connecting the mains water inlet

CAUTION

Excessive bend of connection line

System defect due to impermissible loads on the system!
Reduced service life!

▷

Connect the connection line without transmitting any stresses or strains.
No forces must act on the connection nozzles and the system.

CAUTION

Pressure higher than mains water back-up limit of 4 bar

System defect due to impermissible load!

▷

Install pressure reducers upstream of the system to make sure that the inlet
pressure of the mains water supply does not exceed 4 bar.

CAUTION

Solid substances in the drinking water (stones, sediments, limescale deposits)

System defect due to impermissible loads!
Reduced service life!

▷

If used in areas where the drinking water quality is affected by the above,
provide a drinking water filter.

NOTE

Fitting a shut-off valve at the site is recommended.

741.02

Fig. 3: 

Connecting the mains water inlet

1. Connect the mains water inlet to the mains water supply (float valve 741.02) 

R 

3

/

4

.

2. Open the mains water supply line.

ð

The mains water storage tank will fill automatically once the mains water
supply line is opened.

Summary of Contents for Hya-Rain

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands