manualshive.com logo in svg

KSB Hya-Rain, Installation & Operating Manual

Share
Download
KSB Hya-Rain Installation & Operating Manual Download Page 12

3 Transport/Temporary Storage/Disposal

12 of 64

Hya-Rain/Hya-Rain N

3.3 Storage/preservation

CAUTION

Damage during storage by frost, humidity, dirt, UV radiation or vermin

Corrosion/contamination of the rainwater harvesting system!

▷

Store the system in a frost-proof, roofed area.

CAUTION

Wet, contaminated or damaged openings and connections

Leakage or damage of the rainwater harvesting system!

▷

Only open the openings of the rainwater harvesting system at the time of
installation.

If commissioning is to take place some time after delivery, we recommend that the
following measures be taken for storage:

▪

Store the rainwater harvesting system in a dry, protected room with a constant
atmospheric humidity.

▪

For storing a rainwater harvesting system which has already been operated,
observe the measures to be taken for shutdown.  (

ð

 Section 6.3.1, Page 31)

3.4 Return to supplier

1. Drain the system as per operating instructions.

2. Always flush and clean the system.

3. In addition, anhydrous inert gas must be blown through the system to ensure

drying.

4. Always complete and enclose a certificate of decontamination when returning

the system.
Always indicate any safety and decontamination measures taken.

NOTE

If required, a blank certificate of decontamination can be downloaded from the
following web site: 

www.ksb.com/certificate_of_decontamination

Summary of Contents for Hya-Rain

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands