KSB HPK-L Installation & Operating Manual Download Page 23 | Manualshive

Page: 23 / 74

background image

5 Installation at Site

23 of 74

HPK-L

1136.8/15-EN

5.2.1 Installation on the foundation

L

1

3

2

Fig. 9:

Fitting the shims

L

Bolt-to-bolt distance

1

Shim

2

Shim if (L) > 800 mm

3

Foundation bolt

ü

The foundation has the required strength and characteristics.

ü

The foundation has been prepared in accordance with the dimensions given in
the outline drawing/general arrangement drawing.

1. Position the pump set on the foundation and level it with the help of a spirit

level placed on the shaft and discharge nozzle.
Permissible deviation: 0.2 mm/m

2. Use shims (1) for height compensation if necessary.

Always fit shims, if any, immediately to the left and right of the foundation
bolts (3) between the baseplate/foundation frame and the foundation.
For a bolt-to-bolt distance (L) > 800 mm fit additional shims (2) halfway between
the bolt holes.
All shims must lie perfectly flush.

3. Insert the foundation bolts (3) into the holes provided.

4. Use concrete to set the foundation bolts (3) into the foundation.

5. Wait until the concrete has set firmly, then level the baseplate.

6. Tighten the foundation bolts (3) evenly and firmly.

7. Grout the baseplate using low-shrinkage concrete with a standard particle size

and a water/cement ratio of ≤ 0.5.
Produce flowability with the help of a solvent.
Perform secondary treatment of the concrete to EN 206.

NOTE

For low-noise operation contact the manufacturer to check whether the pump set
can be installed on anti-vibration mounts.

NOTE

Expansion joints can be fitted between the pump and the suction line or discharge
line.

«
...
21
22
23
24
25
...
»

Summary of Contents for HPK-L











































































Reviews:

No comments

Related manuals for HPK-L

Brand: Panasonic Pages: 224

Brand: M&C Pages: 18

mr. steam AromaSteam MS AROMA

Brand: Feel Good Pages: 20

Brand: AMT Pages: 8

Brand: Rietschle Pages: 17

Brand: Carrier Pages: 12

Summit Pumper Vacuum

Brand: Alto Pages: 6

DHH 12 Si control

Brand: STIEBEL ELTRON Pages: 168

Alterma EDHQ011AA6V3

Brand: Daikin Pages: 22

Brand: DAYLIFF Pages: 12

Brand: AMICOCIRC Pages: 13

HydroTap 30009UK

Brand: Zip Pages: 24

Brand: GDH Pages: 24

Brand: Samoa Pages: 82

HOTSPRING HSTK5

Brand: ZANSKAR Pages: 19

Brand: Aquatight Pages: 24

Brand: Q-Pumps Pages: 20

Brand: Galletti Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands