manualshive.com logo in svg

KSB Etanorm V, Operating Manual

Share
Download
KSB Etanorm V Operating Manual Download Page 11

3 Transport/Storage/Disposal

11 of 62

Etanorm V

1228.87/01-EN

3 Transport/Storage/Disposal

3.1 Checking the condition upon delivery

1. On transfer of goods, check each packaging unit for damage.

2. In the event of in-transit damage, assess the exact damage, document it and

notify KSB or the supplying dealer and the insurer about the damage in writing
immediately.

3.2 Transport

 DANGER

The pump (set) could slip out of the suspension arrangement

Danger to life from falling parts!

▷

Always transport the pump (set) in the specified position.

▷

Never attach the suspension arrangement to the free shaft end or the motor
eyebolt.

▷

Observe the information about weights, centre of gravity and fastening points.

▷

Observe the applicable local accident prevention regulations.

▷

Use suitable, permitted lifting accessories, e.g. self-tightening lifting tongs.

CAUTION

Improper pump transport

Damage to the bearings!

▷

Use a suitable transport lock to prevent axial movement of the pump shaft
during transport.

CAUTION

Incorrect transport of the pump set

Damage to the tie bolts.

▷

Do not attach any ropes in the area of the tie bolts 905.

▷

Do not place or support the pump set on tie bolts 905.

When transporting the pump without motor, shaft 210 must be locked with hexagon
head bolt 901.57 and nut 920.75.

To transport the pump/pump set suspend it from the lifting tackle as shown.

Fig. 1: 

Transporting the pump set without/with cover plate up to motor size 160

Summary of Contents for Etanorm V































































Reviews:

No comments

Brands by name

Popular brands

Load more brands