Krone EasyCut F 320 Original Operating Instructions Download Page 66

Page: 66 / 86

Maintenance - Cutterbar

14.2

Replacing shear protection on rotary hub

Original Operating Instructions 150000802_00_en

14.2

Replacing shear protection on rotary hub

NOTICE

Wrong installation position

The machine may be damaged if the installation position of the bearing housings is not

observed.

Clockwise rotating (RH) cutting discs / mower drums always have right-handed pinion

shaft and nut (no groove mark on pinion shaft and nut).

Anti-clockwise rotating (LH) cutting discs / mower drums always have left-handed pinion

shaft and nut (with groove mark on pinion shaft and nut).

KM000-049_1

The machine is in the working position,

refer to page 46

The machine is shut down and safeguarded,

refer to page 23

Dismount sheared off cutting disc or mower drum.

Remove the retaining ring (7).

Unscrew the screws (8).

Dismount the nut (2) by using the special key (10) included with delivery.

Dismount the hub (1).

Remove the damaged shear pins (3).

Check nut and hub for damage.

Summary of Contents for EasyCut F 320























































































Search results

Summary of Contents for EasyCut F 320

Reviews:

Brands by name

Popular brands

Krone EasyCut F 320, Original Operating Instructions

Search results

Summary of Contents for EasyCut F 320

Reviews:

Brands by name

Popular brands