manualshive.com logo in svg

Krone EasyCut F 320, Original Operating Instructions

Share
Download
Krone EasyCut F 320 Original Operating Instructions Download Page 58

11

Maintenance - General Information

11.3

Deviating tightening torques

58

Original Operating Instructions 150000802_00_en

*) Always replace copper rings

11.3

Deviating tightening torques

Screws/nuts

Tightening torque

Nut for shear protection (rotary hub)

300 Nm

Bearing housing for cutting disc

55 Nm

Bearing housing for mower drum

55 Nm

11.4

Venting the friction clutch

NOTICE

Interventions in the friction clutch will lead to a loss of guarantee!

Interventions in the friction clutch change the slip torque. Therefore the machine may be

damaged considerably.

„

Never intervene in the overload protection.

„

Only use KRONE original spare parts.

KM000-072

The friction clutch protects tractor and machine from damage. The friction clutch is designed

with non-adjustable torque M

R

. The the torque is engraved in the housing of the friction clutch

(2).

Venting

ü

The machine is in the working position, 

refer to page 46

.

ü

The machine is shut down and safeguarded, 

refer to page 23

.

„

Remove the universal shaft.

„

Tighten the nuts (1) evenly.

ð

The friction discs are relieved.

„

Turn the friction clutch.

„

Turn nuts back up to the thread runout.

Summary of Contents for EasyCut F 320























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands