background image

 DEVICE DESCRIPTION 

2

7

OPTIBAR 5060

www.krohne.com

04/2021 - 4003591803 - AD OPTIBAR 5060 Exia R03 en

2.3  Flammable products

Atmospheric conditions:

An explosive atmosphere is a mixture of air and flammable gases, vapours, mists or dusts under 

atmospheric conditions. It is defined by the following values

T

atm

= -20...+60°C / -4...+140°F and P

atm

= 0.8...1.1 bar / 11.6...15.9 psi.

Operation outside the specified above standard atmospheric conditions is permitted only via risk 

assessment of the user and additional measures, as necessary.

Operating conditions:

Outside of atmospheric conditions, the explosion protection according to directive 

2014/34/EU (ATEX) – regardless of the zone assignment – is not applicable due to the lack of key 

safety data.

2.4  Equipment category

Category 1G equipment (EPL-Ga equipment)

The devices are installed in hazardous areas requiring equipment category 1G.

Category 1/2G equipment (EPL Ga/Gb equipment)

The process connection element is installed in the separating wall, which separates areas in 

which instruments of category 2G or 1G are required. The electronics housing is installed in 

hazardous areas requiring instruments of category 2G. The sensor is installed in hazardous 

areas requiring instruments of category 1G.

Category 2G equipment (EPL Gb equipment)

The devices are installed in hazardous areas requiring equipment category 2G.

Summary of Contents for OPTIBAR 5060 eDP





























Reviews: