These instructions were intended for use with the Kreg
Precision Router Table Insert Plate. Depending on your
setup and choice of Insert Plate, you may need to make
adjustments as necessary. If you are not using a Kreg
Precision Router Table Insert Plate, please reference your
Insert Plate’s instructions as necessary.
These levelers are designed to help you mount an insert
plate into your shop-built router table top. Unlike the
majority of levelers on the market, this product works
by attaching directly to the bottom of your router table
top, eliminating the need for a supporting rabbet. A hole
cut straight through the table-top, sized exactly to the
dimension of your router table insert plate is all that is
needed to use these levelers.
Before you start...
www.kregtool.com • 800.447.8638
Tools Required:
• 1/8” Allen Wrench (Included)
• #2 Square Drive (Included)
Outils nécessaires :
• Clé hexagonale de 1/8 po (incluse)
• Tournevis carré no 2 (inclus)
Herramientas necesarias:
• Llave Allen de 1/8” (incluida)
• Broca cuadrada #2 (incluida)
Insert Plate
Levelers
Assembly and Instructions
ITEM# PRS3040
RT10168
Version 4 - 5/2018
Assemblage et instructions
Ensamblaje e instrucciones
These unique levelers are self-aligning for easy
installation. Use the curved tab on the Insert Plate
Levelers to locate each Leveler in the corner of the
Insert Plate opening and fasten them in to place using
three 1-1/4” coarse thread screws per leveler. Be
careful not to overtighten.
Thread the eight 1/4-20 x 1-1/2” cup point socket set
screws into the two holes as shown, and thread about
half way in.
Note: The 1 ¼” course thread screws included
are meant to be used on router table tops with
a minimum thickness of 1”. Depending on your
setup, you may find it necessary to purchase your
own hardware to reduce the possibility of the
screws penetrating the surface of the router table
top or not providing enough hold-strength.
The unique design of the Precision Insert Plate
Levelers and adjustable leveling screw system
applies pressure to both sides of the insert plate
so that – once locked in – your Insert Plate stays
flush regardless of the weight applied. The 8
Leveling Screws and 4 Lock-Down screws work
together to keep your insert plate flush with the
router table surface at all times.
Set the eight ¼-20 x 1-½” Set Screws to
approximately the same height and lay the insert
plate into the opening with the router already
attached. The insert plate should be resting
on the eight adjustable set screws. Using the
1/8” Allen Wrench (included), adjust the set
screws from the bottom side of the Insert Plate,
being careful to adjust each screw the same
distance as the other. Adjust the plate as close
as possible to flush with the surface of the router
table top and run your finger along the perimeter
of the insert plate to check that all edges are
flush with the router table top.
If you are using a Kreg Precision Router Table
Insert Plate, Thread the four ¼-20 x 1-3/4”
Phillips Flat Head Machine Screw (Lock-Down
Screws) through the countersunk holes into the
center hole on each leveler and snug down.
Run your finger along the perimeter of the insert
plate again to check that all edges are flush with
the router table top and adjust each set screw
as needed to bring each side of the insert plate
flush with the surface of the router table top.
Step 1:
Mounting the Insert Plate Levelers to the Table Top
Precision Insert Plate Leveler Instructions
Step 2:
Leveling the Insert Plate
English
WARNING:
!
This product can expose you to chemicals including Carbon
1333-86-4 and other chemicals which are known to the State of California to cause
cancer and reproductive harm. For more information go to www.P65Warnings.ca.gov.
Avertissement :
!
Cet article peut vous exposer à des produits chimiques, notamment au
carbone 1333-86-4 et à d’autres produits chimiques reconnus par l’État de la Californie comme
étant la cause de cancers et de problèmes liés aux fonctions reproductrices. Pour plus de
renseignements, rendez-vous au www.P65Warnings.ca.gov.
Advertencia:
!
este producto puede exponerlo a sustancias químicas, incluidas el carbono
1333-86-4 y otros químicos, reconocidas por el estado de California como causantes de cáncer o
daños en el aparato reproductivo. Para obtener más información, visite www.P65Warnings.ca.gov.
