manualshive.com logo in svg

Kramer VS-88DT, User Manual, Page: 20 / 62

Share
Download
Kramer VS-88DT User Manual Download Page 20

Kramer Electronics Ltd. 

 

VS-88DT 

– Configuring the VS-88DT 

18 

 

Network Settings Sub-menu 

The Network Status sub-menu controls DHCP selection and IP network parameters. 

 

Parameter 

Description 

Options 

OFF, ON 

Turns DHCP on and off 

OFF, ON 
Default

—OFF 

IP Settings 

Sets the IP network address  All valid IP addresses 

Netmask Settings  Sets the IP netmask 

All valid IP netmask addresses 

Gateway Settings  Sets the IP gateway 

All valid IP gateway addresses 

 

Note

: When turning DHCP on, the device performs an automatic reset. 

Ethernet Status Sub-menu 

The parameters in the Ethernet Status sub-menu display the TCP/IP communication 
parameters. 

 

Parameter 

Description 

IP Status: 

Displays the TCP/IP address of the device 

Netmask Status:  Displays the TCP/IP netmask of the device 

Gateway Status:  Displays the TCP/IP gateway 

MAC Address: 

Displays the MAC address of the device 

 

FW Version Display 

Displays the firmware version similar to the following: 

V1.1.1123+04A+1.0 

Reset to Default Sub-menu 

 

Parameter  Description 

NO, YES 

Resets the device to default factory parameters 

 

Update Firmware Sub-menu 

 

Parameter 

Description 

Update I/O FW:  Updates the I/O firmware 

 

Summary of Contents for VS-88DT































































Reviews:

No comments