manualshive.com logo in svg

Kramer FC-404NETxl, User Manual, Page: 6 / 53

Share
Download
Kramer FC-404NETxl User Manual Download Page 6

Kramer Electronics Ltd. 

 

FC-404NETxl 

– Defining FC-404NETxl 

4 

 

Defining FC-404NETxl 

This section defines 

FC-404NETxl

.  

 

Figure 1: FC-404NETxl 4x4 Audio and Dante Mixer

 

Front Panel 

# 

Feature 

Function 

  OUT LEDs (1 to 4) 

Lights green when a signal is present, lights red when clipping is detected.

 

 

IN LEDs (1 to 4) 

Lights green when a signal is present, lights red when clipping is detected.  
Use the embedded web pages to select line level, mic level or 48V for each 
input.

 

  SYNC LED 

Lights green when Dante network is available or red if an error occurred.

 

 

SYS LED 

Lights green for digital audio normal operation. 
Flashes green when this unit is the Master clock. 
Lights red if an error has occurred.

 

  Rx LED 

Lights green when an RS-232 signal is received.

 

  Tx LED 

Lights green when an RS-232 signal is transmitted.

 

 

HEADPHONES 
3.5mm Mini Jack 

Connect to a headphone set.

 

 

ON LED 

Lights green when the device is powered.

 

 

Figure 2: FC-404NETxl 4x4 Audio

 and Dante Mixer

 

Front Panel 

# 

Feature 

Function 

 

AUDIO INPUTS 3-pin Terminal 
block Connectors (1 to 4) 

Connect to analog balanced mono line/mic level (with selectable 
48V) sources.

 

 

AUDIO OUTPUTS 3-pin 
Terminal block Connectors  
(1 to 4) 

Connect to analog balanced mono line level acceptors.

 

 

Dante RJ-45 Connector 

Connect to Dante audio via the network. Provides 4 Tx channels 
and 4 Rx channels. By default, DHCP is enabled.

 

 

RS-232

 

3-pin Terminal Block 

Connector 

Connect to a PC/serial controller.

 

 

ETHERNET

 

RJ-45 Connector 

Connect to a PC via a LAN. 

 

 

RESET Recessed Button 

Reset/reboot the device: press and release the button. 
Reset to factory default values: press and hold the button for 30 
secs.

 

 

12V DC Power Connector 

12V DC connector for powering the unit.

 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14 

15 

Summary of Contents for FC-404NETxl






















































Reviews:

No comments