manualshive.com logo in svg

KRAL CGF, Operating Instructions Manual

Share
Download
KRAL CGF Operating Instructions Manual Download Page 62

17 Appendix

17.1 Tightening torques for screws with metric screw threads with and without wedge lock washers

16.8.2

Tool set, radial shaft seal

Qty.

Part

E

1

Mounting arbour radial shaft seal ring

B

1

Mounting sleeve main screw

C

1

Mounting sleeve ball bearing

17 Appendix

17.1 Tightening torques for screws with metric screw threads with and without wedge lock

washers

Notice

In the case of galvanised screw plugs and screw plugs made of stainless steel the inner thread and
outer thread have to be greased thorough before mounting in order to prevent threads from seizing.

Notice

The manufacturer recommends tightening screws with wedge lock washers according to the table
three times after another with the same tightening torque.

Tightening torque [Nm]

Screws with head contact surface

Countersunk screws

Stainless steel screws A2 and A4

Thread

5.6

8.8

10.9

8.8+
Alu*

Property class
70

Property class
80

8.8

M 3

0.6

1.5

–

1.2

–

–

1

M 4

1.4

3.0

4.1

2.3

–

–

2

M 5

2.7

6.0

8.0

4.8

3.5

4.7

5

M 6

4.7

10.3

14.0

7.6

6.0

8.0

9

M 8

11.3 25.0

34.0

18.4

16.0

22.0

14

M 10

23.0 47.0

68.0

36.8

32.0

43.0

36

M 12

39.0 84.0

117

64.0

56.0

75.0

60

M 14

62.0 133

186

101

–

–

90

M 16

96.0 204

285

155

135

180

100

M 18

133

284

390

224

–

–

–

M 20

187

3999

558

313

280

370

135

M 24

322

687

960

540

455

605

360

Tab. 23: Tightening torques metric screw thread

*When screwing into aluminium, the tightening torque reduces by 20 % when the screw-in depth is less
than double the thread diameter.

62

OIC 18en-GB Edition 2020-01

Operating instructions

Summary of Contents for CGF

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands