manualshive.com logo in svg

KRAL BEM 300 Series, Operating Instructions Manual

Share
Download
KRAL BEM 300 Series Operating Instructions Manual Download Page 10

10

OIE 15en  Edition 2019-12 HW 2.0/SW 2.0 

Operating Instructions

Unpacking and checking the state of delivery

Transportation, storage and maintenance

Transportation, storage and maintenance

Unpacking and checking the state of delivery

1. On delivery unpack the electronic unit and check for damage during transportation.
2. Report damage during transportation immediately to the manufacturer.
3. Dispose of packing material in accordance with the locally applicable regulations.

Transportation

► If possible, transport the electronic unit in the original packaging, while observing the ambient condi-

tions, see "Ambient conditions", page 18.

Storage

► If possible, store the electronic unit in original packaging in a cool and dry place, while observing the 

ambient conditions, see "Ambient conditions", page 18.

Disposal

Safety instruction for disposal

Disposing of the electronic unit

► As electronic waste the electronic unit has to be disposed of properly.

Maintenance

The electronic unit is maintenance-free.

Cleaning

In order to clean the electronic unit wipe the housing with a soft cloth. In case of stronger soiling moisten 
the cloth with water that has a common detergent added. Only wipe the surface off lightly with a moist 
cloth. Under no circumstances may water penetrate the inside of the electronic unit!

The following safety instruction must be observed during disposal:

► Observe the local regulations on disposal.

Summary of Contents for BEM 300 Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands